Monday, September 22, 2014

TUTORIAL : How to make a (super adorable) USB Flash Drive case

Yes, you are in the right place.  And yes, this is not a recipe!  It's sewing-related!!!!

Remember this? Can't believe it's been more than two and a half years and still no tutorial.  I must really apologize for my lack of commitment to that promise.  To my readers who originally came here for the sewing, I am so sorry that you have found no sewing activity here for so long!

Since it's the school holidays, I made this plan to finally make the tutorial.  It seems I got too excited to sew, that yesterday, in between breakfast and lunch, I finished the whole thing!

Isn't that absolutely adorable?



This is in fact a one-sitting kind of project.  It's pretty easy.  However, I would still recommend it for people who have some sewing experience particularly in bias binding and sewing over multiple fabric layers and around curved seams.  I have had no practice in tutorial-making for sometime now so I might be making unclear instructions here and there that beginners will find hard to understand. Still, if you are new to sewing and are interested to make one of these cases, just consider it a challenge!

HOW TO MAKE A USB FLASH DRIVE CASE

Materials:

fabric scraps
small piece of fusible fleece
small piece of plastic
25" long two-inch wide bias tape**
one 2" long velcro
one key ring or swivel hook

**It is best to just make this yourself as you are only going to need a small length.  If you don't know how, learn from here.  You need to cut 2" wide strips.  Keep the tape open for now (no need to fold it).

Procedure:

1.  Download the pattern from here.  Print it out in Actual Size.

2.  Cut out the pattern pieces then use them to cut out your materials.

     A: Cut two pieces from outer fabric for the flaps .
     B: Cut one piece for the lining.
     C: Cut two pieces from fusible fleece.
     D: Cut two pieces from plastic.

     In addition, cut three 2"x 2" squares from outer fabric.


3.  Iron on fusible fleece to the back sides of the flap pieces.


4.  Take one of the 2" square pieces,  Fold it in half to create a crease then open again.  Fold two opposite sides towards the center crease then fold again to end up with a 1/2" wide strip. Iron.  Do this for the other two 2" squares.


5.  Take one of the strips and stitch along the two long sides, about 1/8" from the edges.  Insert your key ring (or swivel hook) then bring the raw edges together to make a loop.  Sew the raw edges together.


6.  Center your key ring loop on the straight side of one of your flap pieces.  Baste.


7.  With right sides facing (with key ring loop inside), sew the two flaps together.  Sew right where the end of the fusible fleece is.


8.  Open up your flaps, right side up.  The seams will naturally fold towards one side (in my case, downward), in the opposite direction of the key ring loop.  Topstitch very near the center stitching where the two flaps were sewn together, catching the seams at the back.


9.  Insert the remaining two 1/2" wide strips (from step 4) into the straight edges of your plastic pieces.  Topstitch close to the inside edges.


10.  With wrong sides facing, baste together your assembled flaps and lining.


11.  Position your two plastic pieces on the two ends then baste.  If you are having trouble with sewing over the plastic, stick a small piece of magic tape on the underside of your presser foot so it will move smoothly.


12.  Position your velcro 1" from the top of the curve on both ends. Stitch along the long sides of the velcro.  Cut off the excess velcro, following the shape of the curve.



13.  Fold one end of your open bias tape 1/4" in, then fold the whole length of the tape in half lengthwise and iron flat.



14.  Pin your bias tape to the plastic side of the case, aligning the raw edges.  Using a 1/4" allowance, sew the bias tape all around. (I did not find pinning necessary but I sewed very slowly.) When you reach the end, overlap the tape by about 1" then cut off the excess.

It doesn't really matter where you start sewing.  However, if you have a preferred front flap for your case, start sewing the bias tape on what would be the back flap.

15.  Turn the bias tape over to the other side.  If it seems too tight, trim a bit off the seam allowance.  Iron this if you need to but just remember there's plastic underneath!



16.  Slipstitch the bias tape by hand, making sure you are concealing the raw edges and any stitching.


Yay!  That's it!  Now put your flash drives into the plastic pockets. Secure with the velcro closure.


You can attach this to your bag, use it as a keychain or hang it somewhere near your computer.  Never misplace your flash drives again!


Hope you will have fun making this simple project!





1 comment: